BREMSHEY ORBIT PLUS MANUAL PDF

You can find the manual for your Bremshey Cross Trainer below. Bremshey Orbit Ambition Cross Trainer · Bremshey Orbit Control Cross Trainer · Bremshey. Check the reed sensor also known as the speed sensor. It is located on the front roller pulley. It is mounted to the frame and looks like a small. 18TSFC_Star Fit C HR i-Plus Crosstrainer_OMpdf . _Bremshey Orbit Ambition C_User Manual. pdf. MB.

Author: Bazil Kazishakar
Country: Belarus
Language: English (Spanish)
Genre: Video
Published (Last): 7 March 2017
Pages: 232
PDF File Size: 15.84 Mb
ePub File Size: 19.92 Mb
ISBN: 464-7-86804-568-7
Downloads: 21490
Price: Free* [*Free Regsitration Required]
Uploader: Yozshutaxe

Check connections and wiring from sensor to meter. If treadmill recovers to normal operation, you may continue to use the treadmill.

Manuals for Bremshey Cross Trainers

See diagram 17 above Warning! Measure electromagnet coil total resistance, it should not be zero or infinite.

Adjust the drive belt tension. Slide the deck out sideways from the frame. Insert commutator stone and press against copper commutator. If the belt is running out towards the covers bend the arm towards the frame.

Owing to specification variations some of the information is generalised to cover the complete range. Install new belt on the front roller and re-install bolt. Lift motor rotation sensor potentiometer cable disconnected Lift motor rotation sensor has poor internal contact and is thus providing incorrect values The second connection cable between the console and bremshe lower board is disconnected The potentiometer has lost its calibration and rotated to minimum If the readout from the potentiometer has lost its calibration setting and it differs from reference values, adjust potentiometer Figure 1 to obtain correct value.

  LA SAGA DE DHAMON PDF

Bremshey Sport :: Manuals

Inside the foot-tube joint is a sealed self-aligning bearing held in place by an internal circlip. It is very important that these areas are well lubricated with grease and this should be carried out as a part of a general service. Checking and setting belt alignment. LED scanning mode for verifying display functionality 3. We recommend that at this point the lower adjuster bolt i is unscrewed, the spring that is sometimes located at the bottom of the vertical bremahey bar is removed, and the adjusting bolt re-fitted bremshdy not tightened.

To achieve this, the tension must be released from the cable. Can you hear servo-motor operating? It is quite rare for the electromagnetic coil to fail.

Rotate the drum as indicated previously.

Bremshey Orbit Fit (4182b) Cross Trainer

Before removing the covers from a machine powered by mains transformer it will be necessary to remove the power socket from the rear of the cover. Continue to rotate the drum whilst forcing the belt to remain in place with your hand.

Check connection and restart PC if needed. Therefore, in order to test the servo-motor brake mechanism the sensor must receive constant pulses by rotating the rear pous.

  ANALISIS SWOT TEKNIK MEMBEDAH KASUS BISNIS PDF

Bremshey Orbit Control Cross Trainer

The other alternative is to Re-install brush port covers. Do not switch off the product during the recovery. The question will be displayed again after restart. From there the machine is grounded using a three-pronged plug into the wall. Be careful not to trap fingers at this point.

Separating drum cover and cross frame assemblies A standard Shimano style crank puller and adaptor will be required. Defective cable or connector between the bremwhey interface and lower oorbit a.

Original parameters are written on label attached to the product frame post inside side covers. Check Ear Sensor replace. Additionally, the tread will have very fine metal wires running through it to help reduce static build up on the belt caused by the friction between the belt and the rollers.

These are controlled mechanically by the rotation manuxl a control knob or electromechanically by use of a servo-motor.

To replace the bearings: To access the internal components of the Orbit it is necessary to remove one or both sides of the main cover sets.